Workingman Posted June 22, 2020 Report Share Posted June 22, 2020 (edited) Very mice. A bit like a fancied up Gretsch sound-hole. Edited June 22, 2020 by Workingman 1 Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted June 23, 2020 Author Report Share Posted June 23, 2020 And the purfling is in. Next is the swift inlay and then I can cut out the soundhole, using the same Dremel radius jig so that the corners are concentric with the detailing. 3 Quote Link to comment Share on other sites More sharing options...
Popular Post Andyjr1515 Posted June 24, 2020 Author Popular Post Report Share Posted June 24, 2020 The inlay is done in the same way as normal with the Dremel precision router base to cut out the chamber, having pencilled round the inlay to give me the outline: Next was cutting out the soundhole itself. I used the Dremel radius jig and same centre holes and a straight edge guide as for the purflings, but this time with the router bit at full wood depth. It did feel a bit like the guy sitting on the thin side of the branch he was sawing off! But, luckily, all was well. Still got to tidy it all up but it's basically done ready for the dishing and braces to be applied: Meanwhile, I started on the body mould. My admiration for the prehistoric engineers who sorted out getting the uprights square and vertical on Stonehenge has made a great leap: Gluing time will tell whether any of that has passed on down through the gene pool: 4 1 Quote Link to comment Share on other sites More sharing options...
ScottR Posted June 24, 2020 Report Share Posted June 24, 2020 1 hour ago, Andyjr1515 said: It did feel a bit like the guy sitting on the thin side of the branch he was sawing off! 1 hour ago, Andyjr1515 said: My admiration for the prehistoric engineers who sorted out getting the uprights square and vertical on Stonehenge has made a great leap: 1 hour ago, Andyjr1515 said: Gluing time will tell whether any of that has passed on down through the gene pool: Always entertaining Andy! And instructive. And impressive. This is good stuff! SR 1 Quote Link to comment Share on other sites More sharing options...
Prostheta Posted June 24, 2020 Report Share Posted June 24, 2020 Look Scott, plywood! 1 Quote Link to comment Share on other sites More sharing options...
curtisa Posted June 25, 2020 Report Share Posted June 25, 2020 Not just any plywood. Guizouki plywood! Much richer tone. Fuller. More moreness. And unicorns. 1 Quote Link to comment Share on other sites More sharing options...
Prostheta Posted June 25, 2020 Report Share Posted June 25, 2020 I'm really liking your setup as well Andy. Much more organisable and usable. Those dog hole clamps are a great boon. Perhaps since I might have to move towards more hand tool work, a tail vise and various dog holes would be in my near future also. Plywood! For many success and great happy. 1 Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted June 25, 2020 Author Report Share Posted June 25, 2020 40 minutes ago, Prostheta said: I'm really liking your setup as well Andy. Much more organisable and usable. Those dog hole clamps are a great boon. Perhaps since I might have to move towards more hand tool work, a tail vise and various dog holes would be in my near future also. Plywood! For many success and great happy. I agonised over that workbench. Never having had one or any sort in the past - you remember my workmate days - I was a bit in the dark (and in the cellar, literally!) about what features I should be considering. But I'm very pleased with what I eventually chose. And the dog hole clamps are the feature that - without any doubt - I use the most. There are so many things where I have no idea how I would do it without them! So it was worth all the agonising! Quote Link to comment Share on other sites More sharing options...
ADFinlayson Posted June 25, 2020 Report Share Posted June 25, 2020 Love the sound hole Andy, This build couldn't come at a better time for me - I've got OM moulds and plans on the way 2 Quote Link to comment Share on other sites More sharing options...
Prostheta Posted June 25, 2020 Report Share Posted June 25, 2020 Totally. The first mistake one can make with a workbench is a lack of weight and thickness in the top. Dog holes and holdfasts need that to work, plus any work with a hand tool needs the workbench and workpiece to stay put. 1 Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted June 25, 2020 Author Report Share Posted June 25, 2020 Thanks, folks This morning, I cut out the top, around 10mm oversize all round at this stage. I know it's small beginnings, but this - to me at least - is still a very pleasing start: So next jobs, while I'm sourcing the bracing woods, is preparing to bend the sides. But first, I have to cut them to shape (a LOT easier than trying to cut them once they have been bent - and don't ask me how I know!). Basically, the sides themselves will reduce from around 95mm deep at the heel to around 80mm at the neck. But - that's not a straight line. Because of the waist, the back side of the side piece does a double elongated s-curve - and where and how much that is, depends on the waist shape. Now, I'm sure a decent CAD package (or a cheap one with a decent operator) could sort it out in minutes. But I use CAD so infrequently, it would take me as long to work out how to do it than just cut a cartridge-paper template, put it into the mould and eyeball it (you look at the mould from the side and mark a straight line in dots from one end of the paper to the other and, when you stretch it out again and join up the dots, it will be - miraculously - the correct stretched out S you want. Pictures will make that easier to explain. I'll photograph it as I do it 2 Quote Link to comment Share on other sites More sharing options...
ScottR Posted June 25, 2020 Report Share Posted June 25, 2020 17 hours ago, Prostheta said: Look Scott, plywood! Yeah, that's like what I can get. As opposed to the 37 ply to the inch stuff you have. SR 1 Quote Link to comment Share on other sites More sharing options...
Prostheta Posted June 25, 2020 Report Share Posted June 25, 2020 It could even be Okoumé plywood. I see a lot of that in marine. 1 Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted June 26, 2020 Author Report Share Posted June 26, 2020 And so to the shape of the sides blank. Normal warning as with all my threads - I'm happy to describe what I do and why...but please never assume this is how or the best way it should be done I start off with a rectangular sheet of cartridge paper taped so that it follows the outer shape of one of the sides in the mould. The bottom edge represents where the top will be and the top edge where the bouzouki back will be: So eyeballed edge on, this is how it looks: In broad terms (there are foibles I'll cover in later posts), edge on like this, we will want the back to go from 105mm (plus the top and back at 5mm total will give a final tail end depth of 110mm) to 85mm at the heel (total heel depth ending at 90mm) in roughly a straight line. So what I do is mark the 105 at the back and 85 at the front, and pack up a straight edge to that angle: I then run a metal ruler at 90 degrees to and along the top of the beam and mark spots on the paper all the way from the tail to the heel: So I then end up with a series of dots all the way along the paper which I join up and then cut out with scissors. And, although this is not perfect, it is close enough to be able to use as the basis of fitting the back at the appropriate time: And stretched out, you can seen that this is a million miles away from a straight line between the two points: And - although it is very subtle, I can see the concave curve at the heel end, changing to a convex curve at just under halfway - which makes me think that my attempt is at least in the right ball-park So next job is thicknessing the sides to around 2mm and then cutting them to this shape - and then the scary bending can begin 1 Quote Link to comment Share on other sites More sharing options...
Popular Post Andyjr1515 Posted June 27, 2020 Author Popular Post Report Share Posted June 27, 2020 One of the reasons for the detailed threads is to remember what I did last time. Like thicknessing the sides from 4mm to 2mm. Clearly not the block plane. But was it my No5 Bailey plane? Or scrapers? Or my scraper plane? Surely I didn't sand it? Well - tried them all. This one (the No 5) should have been the best: No - I remembered when in desperation I picked it up and tried it anyway. Yup - the block plane that 'isn't suited to this kind of task'. Sorted it in about 30 minutes And so cut them out to the template above's shape and soaked them both in the bath for a decent time: Primary tool is the electric bending iron: And then, coming up the bench towards the camera, it's a water spray bottle, sturdy gloves, the mould and - a flash of inspiration - the bits of body-shaped ply offcuts from making the mould stacked together and held tight in a vice: Red Gum walnut is new to me, but generally walnut is quite good to bend. But - that waist is as tight a bend as any I've tried. I moved the bending iron round to the sharper radius and worked slowly and carefully, re-soaking the wood frequently. It is VERY easy for the wood fibres to split if you over do it or - worse - snap. And if it snaps, it's a whole new back and side set - they are matched so you can't just get a set of sides! Doing it by hand, I could get to within 15 degrees of the required bend but just couldn't get it further. Then had the inspiration with those body-template offcuts. Could I pretend this was a Fox bender without the heat? And it b****y well worked!!!! The near clamp was just to hold the sheet in the right place and the far clamp - that started around an inch above the mould, just gently and continuously brought it closer and closer until it was fully in the waist 'V'. No splits, no cracks, no need to buy a new back and side set! So this is all in and will hold its shape pretty well when fully dry, but I will keep it in the mould until the edge kerfed strip has been put on top and bottom and then it will completely hold its shape even out of the mould 6 1 Quote Link to comment Share on other sites More sharing options...
Workingman Posted June 28, 2020 Report Share Posted June 28, 2020 Nice. since you are dabbling on the edges of mandolin world, you should take a look at F style mandolin scrolls if you want to see tight curls. 1 Quote Link to comment Share on other sites More sharing options...
ADFinlayson Posted June 28, 2020 Report Share Posted June 28, 2020 Fantastic work Andy, if you hadn't gone into detail about the taper along the back of the sides, I'd have cocked that up! I picked my plans up from the printers yesterday and my mould is arriving on Monday, so excited 1 Quote Link to comment Share on other sites More sharing options...
ADFinlayson Posted June 28, 2020 Report Share Posted June 28, 2020 What's the rationale behind putting the bending iron on it's side? is it easier to keep the bend square? I was toying with making some sort of table that the iron could sit in and keep the sides flush on the table to keep them square - when I was bending some little binding pieces to go around a truss rod cover, I saw how easy it is to bend a twist into the work. Quote Link to comment Share on other sites More sharing options...
curtisa Posted June 28, 2020 Report Share Posted June 28, 2020 11 hours ago, Andyjr1515 said: Red Gum walnut is new to me New to me too. Red Gum - yes: https://en.wikipedia.org/wiki/Eucalyptus_camaldulensis Walnut - yes: https://en.wikipedia.org/wiki/Juglans Red Gum Walnut? Sounds like someone wasn't sure if it was Red Gum or Walnut when they put it up for sale Either way, doesn't matter. It's looking splendiferous at the moment. The Guitar Bouzouki is already a hybrid instrument; may as well use hybridised timbers to build it 1 Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted June 28, 2020 Author Report Share Posted June 28, 2020 It's also called Satin Walnut. I'll check when I get a moment, @curtisa but it's probably an insect or fungal description rather than a species, a bit like spalted stuff. Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted June 28, 2020 Author Report Share Posted June 28, 2020 7 minutes ago, Andyjr1515 said: It's also called Satin Walnut. I'll check when I get a moment, @curtisa but it's probably an insect or fungal description rather than a species, a bit like spalted stuff. And also called Sweetgum. It's here: https://www.wood-database.com/sweetgum I was wrong about the insect, fungal stuff. It is indeed a species. Liquidambar styraciflua Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted June 28, 2020 Author Report Share Posted June 28, 2020 6 hours ago, ADFinlayson said: I picked my plans up from the printers yesterday and my mould is arriving on Monday, so excited Me too! 6 hours ago, ADFinlayson said: What's the rationale behind putting the bending iron on it's side? is it easier to keep the bend square? I was toying with making some sort of table that the iron could sit in and keep the sides flush on the table to keep them square - when I was bending some little binding pieces to go around a truss rod cover, I saw how easy it is to bend a twist into the work. You can do it either way, @ADFinlayson I do it this way because it takes controlled, sustained force while, as you say, keeping everything square. That's difficult when you are using just muscle power - so I am using body weight as the force and muscles as the control 1 Quote Link to comment Share on other sites More sharing options...
Popular Post Andyjr1515 Posted June 28, 2020 Author Popular Post Report Share Posted June 28, 2020 All dry, so this morning I got to add the neck and tail blocks: Although it will become much stiffer once the kerfed strips are put all the way round the edges top and bottom (these are the strips that the top and the back of the body will eventually glue onto), it's already holding its shape pretty well: 5 Quote Link to comment Share on other sites More sharing options...
ScottR Posted June 28, 2020 Report Share Posted June 28, 2020 Damn. Good stuff Andy! SR 1 Quote Link to comment Share on other sites More sharing options...
Bizman62 Posted June 29, 2020 Report Share Posted June 29, 2020 I keep coming back to look at your mould! So little material lost compared to the other ones I've seen. And much less work to sand the inside flush. Who knows, maybe someday I'll copy that design to make an acoustic! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.